Overheating laptop and related shutdown problems are very common in notebook computers, especially in home use. Common symptoms of laptop overheating include some or all from this list;
- Laptop is extremely hot to the touch, especially around the fan exhaust area
- Laptop fan is constantly running at high speed
- Laptop shuts down by itself when doing nothing
- Laptop shuts down when playing games
- These laptop overheating or shutdown problems become worse over time, rather than getting better.
In around 1 in 10 cases of laptop overheating, there is potentially a physical fault with the cooling hardware.
By this I mean either a mechanical failure with the fan where it can no longer spin, or it spins too slowly, or a motherboard electrical fault which exhibits itself by not telling the fan to spin fast enough to cool the laptop.
However 9 out of 10 cases of laptop overheating are caused by an airflow blockage.
In these cases, the fan is spinning as fast as it can, but if the hot air is obstructed from reaching the outside world, a heat build-up occurs and the laptop takes the safety precaution of turning itself off, rather than allowing permanent damage to occur.
I will very quickly explain how a laptop cools itself.
Heat from the CPU, and sometimes the graphics chip, is conducted away from the processors via strips of copper metal. At the far end of this copper heatsink, the heat is fed into a series of side-by-side metal fins. This grill provides a very large surface area for the heat to be spread over.
A fan then draws air from the outside world and blows across the hot grill, back towards the outside. As it does so, the air picks up heat from the hot metal fins and takes it away from the laptop.
In an laptop overheating due to an airflow obstruction scenario, the most likely culprit is a build-up of material in front of the metal heatsink grill.
The fan will be drawing in cool air from the outside world through vents in the bottom or sides of the laptop and occasionally there might be a tiny piece of fluff, hair or dust sucked in with the cool air.
When this air is being blown across the hot metal grill, the airborne material can get stuck on the front of the metal fins if it is large enough.
If this keeps happening over time, gradually more and more material will build up on the front of the grill, creating an obstruction.
A common example of this buildup of material is shown in the image to the left. All of that grey furry material is a combination of dust, lint, hair or fluff that has been compacted on to the front of the heatsink grill.
The effect of this is to block some of the airflow over the heatsink grill. With less physical space for the air to get through, the air is not picking up heat from the whole set of fins.
So a smaller amount of heat is transferred to the air in it’s journey to the outside world. With less heat being removed, the heat starts to build up inside the laptop (overheating).
Temperature sensors detect this and will react by making the fan spin faster and faster. The point of spinning the fan faster is to force more air through the available gaps, and past the hot metal fins to pick up more heat.
This compensation of spinning the fan faster can work to an extent, but eventually a limit will be reached. If the heatsink grill is sufficiently blocked, the fan will be spinning at maximum speed and it will no longer be possible to reduce, or even stabilize, the internal temperature of the laptop.
Temperature sensors will realize this and as a final fail safe protection measure the laptop will power itself off. The hope behind this is that if the CPU is no longer producing more and more heat, the existing internal heat will gradually dissipate of it’s own accord and the laptop will, hopefully, avoid serious damage.
To fix this problem, you need to strip the laptop down to allow access to the heatsink and fan(s).
I’m not going to explain how to strip down a laptop, step by step, as there are guides elsewhere explaining this in detail, and some manufacturers, for example Dell, even provide Service Manuals on the support pages of their website.
In most cases, to disassemble a laptop, all you will need are one or two small screwdrivers.
Some laptops require special torque screwdriver heads to remove some of the internal screws, so you will need to investigate this in relation to your particular laptop make and model.
Each make and model of laptop will have it’s own threshold as to how much obstruction there can be before it causes a problem. I’ve seen cases where there is a large solid strip of dust and fluff, several millimeters thick, that peeled away in one large piece.
After brushing away most of the dust build-up, you should gave the heatsink fins and the fan a good blast with compressed air.
This blows away the last remnants of dust, and leaves a nice clean shiny heatsink grill and fan.
All that remains is to reassemble the laptop using the same steps as before, except in reverse.
The laptop is now working well and no longer overheats or shuts off by itself. A side-benefit of this fix is that the laptop now runs a lot more quietly.
Because the fan can now remove the excess heat in the laptop while running at a slower speed, it reduces the fan noise. The laptop is also a lot cooler to the touch.
Please check back with us as we’ll be starting a bi-weekly series beginning in July with articles covering various tips, tricks, fixes, etc for your digital world.
Feel free to contact us if there are any topics you’d like to have addressed as well.